|
Size: 101
Comment:
|
← Revision 17 as of 2013-09-18 06:09:34 ⇥
Size: 2215
Comment: converted to 1.6 markup
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 1: | Line 1: |
| ## page was renamed from updating ccpde | |
| Line 2: | Line 3: |
| attachment:e:\bht-options.JPG Describe updating ccpde here. | The CCPDE program is a program that runs in BHT BASIC, the source file resides in the std/pde directory called ccpde.src. There is a BHT BASIC compiler, (30 day trial period), located in the knowledge database hardware/pde/denso/bhtdev4t/BASIC/setup.exe. Need to remember to compile program as a BASIC 3.6 and to turn off option to causes errors for undefined variables. Other wise just refer to the manual – also located in the knowledge database. Once compiled this should create a ccpde.pd3 file. To download the program onto the PDE Unit hold down SF, 1 and PW keys at the same time to get the System Menu. You may need to setup the communication setting of the PDE unit first. . 4:SET SYSTEM . -> 5:COMMUNICATIONS . -> 2:CONNECTOR . -> 1:PARAMETER - should be set to . 1:TRANSMIT SPEED : 19200 . 2:PARITY BIT: N . 3:DATA 8 . 4:STOP 1 . -> 3:COM PORT . 1:BASIC – Connector . 2:SYSTEM MODE – Connector . -> 4:PROTOCOL TYPE . 2:BHT-IR Protocol ==== Important note: ==== ==== Turn the unit over, if the serial number ends in 04xxx, you will encounter serveral problems. First of all, TSR-tu3a will not be able to send ANYTHING. This is because the last 5 digits of the serial number is used as the BHT-Ir ID. If it starts with 04, this has a special meaning to the communications (EOT) and it gets interpreted as such. If the unit has a serial number ending in 04xxx, go into 4:PROTOCOL TYPE -> 2:BHT-Ir Protocol and enter a different number, such as 14xxx. You will be able to proceed as normal. ==== To download the CCPDE program press 2:DOWNLOAD -> 1:FILE and then on the PC send the CCPDE.PD3 file using TSR-tu3a (located in knowledge database) transfer Utility (don’t forget to set the communication Parameters to 19200,N,8,1). After the program is downloaded you could call 1:EXECUTE PROGRAM then CCPDE.PD3 or just turn the unit off and back on again will start the CCPDE program giving the following Menu. . 1.COLLECT . 2.COLLECT COUNT = 1 . 3.UPLOAD COUNTS . 4.DOWNLOAD MASTERFILE . 5.DELETE MENU ---- . [[CategoryPDE]] |
Updating CCPDE program for Denso
The CCPDE program is a program that runs in BHT BASIC, the source file resides in the std/pde directory called ccpde.src.
There is a BHT BASIC compiler, (30 day trial period), located in the knowledge database hardware/pde/denso/bhtdev4t/BASIC/setup.exe. Need to remember to compile program as a BASIC 3.6 and to turn off option to causes errors for undefined variables. Other wise just refer to the manual – also located in the knowledge database. Once compiled this should create a ccpde.pd3 file.
To download the program onto the PDE Unit hold down SF, 1 and PW keys at the same time to get the System Menu.
You may need to setup the communication setting of the PDE unit first.
- 4:SET SYSTEM
-> 5:COMMUNICATIONS
-> 2:CONNECTOR
-> 1:PARAMETER - should be set to
- 1:TRANSMIT SPEED : 19200
- 2:PARITY BIT: N
- 3:DATA 8
- 4:STOP 1
-> 3:COM PORT
- 1:BASIC – Connector
- 2:SYSTEM MODE – Connector
-> 4:PROTOCOL TYPE
- 2:BHT-IR Protocol
Important note:
Turn the unit over, if the serial number ends in 04xxx, you will encounter serveral problems. First of all, TSR-tu3a will not be able to send ANYTHING. This is because the last 5 digits of the serial number is used as the BHT-Ir ID. If it starts with 04, this has a special meaning to the communications (EOT) and it gets interpreted as such. If the unit has a serial number ending in 04xxx, go into 4:PROTOCOL TYPE -> 2:BHT-Ir Protocol and enter a different number, such as 14xxx. You will be able to proceed as normal.
To download the CCPDE program press 2:DOWNLOAD -> 1:FILE and then on the PC send the CCPDE.PD3 file using TSR-tu3a (located in knowledge database) transfer Utility (don’t forget to set the communication Parameters to 19200,N,8,1).
After the program is downloaded you could call 1:EXECUTE PROGRAM then CCPDE.PD3 or just turn the unit off and back on again will start the CCPDE program giving the following Menu.
- 1.COLLECT
- 2.COLLECT COUNT = 1
- 3.UPLOAD COUNTS
- 4.DOWNLOAD MASTERFILE
- 5.DELETE MENU